Home networking can be a real pain especially for someone like me who knows enough to be dangerous but not enough to be a network installer. I have a wireless router burried in my basement that wasn't getting signal to my upstairs part of the house. I tried two other different products 1) two routers connected to each other and 2) a Hawking repeater. I ended up wasting a lot of time with them and they just didnt work or had compatibility issues. I took a plunge on the no brand trendnet based on this other positive review and he was 100% right. The price is 50% cheaper than the comparable Linksys N switch and does exactly as advertised. Setup took 5 minutes and I now have coverage all over my house. No issues so far.
Original review:
I have had this AP for a few months now. It was not difficult to set up at all. When it works properly, I get decent speeds. However since this is a 2.4GHz access point don't expect channel bonding to work as well as in a 5GHz or dual band unit because the 2.4GHz band is basically overloaded. Also, this access point only comes with a 100BaseTX wired ethernet interface, so even if you got more than 100Mbps on the wireless side you're limited by the wired interface.
I also have it set up with WPA2, initially with WPA2-PSK and now with WPA2 enterprise using FreeRADIUS on pfsense for better security.
It does have multiple SSIDs but what is the point of that? It's not like you can segment it into VLANs or anything so this is a pointless feature. This would have been useful because I could keep one SSID open and put it on a DMZ on my firewall so I can give guests wifi access without opening up my whole network.
That said, my access point refuses to connect every ever so often. Completely random, but usually after I've completed some large file transfers over N wireless. It almost seems as though some buffers in the device are being saturated and the device just locks up. My laptop or iPod will attempt to associate then fail with no explanation, then magically come back after I power cycle the device.
I have not seen any firmware updates for it that would fix the issue so I think I'll just attempt to get warranty service for it or just get another access point like a Cisco.
Buy TRENDnet 300Mbps Wireless N Access Point TEW-638APB (Black) Now
The documentation that comes with the product is poor. The web site is not very informative.My access point had a non-standard default password when reset to factory defaults. I had to guess to figure it out.
I bought two to set up a network for a larger area. Figuring out how to do it was a process of trial and error. In the "Knowledge Base" on the TRENDnet web site, it's hard to tell which access point needs to be configured in what way in order to get it to work.
I could forgive these problems. However, when conducting large data transfers over a secure network (think backup) it would reboot itself. Often, when it did so, it would forget it's entire configuration. Fortunately, I backed up the configuration to a file. It's annoying to have to manually fix my access point every few weeks... more often when it's hot.
Eventually I bought a netbook cooler (with a fan) to put the thing on. That helped... now it does not reboot and loose its mind so often... but it still does occasionally.
Stay away from this junk. I used to love TRENDnet because they had good quality products for good prices. Now, I will stay away from TRENDnet products. An item this expensive should have better documentation and should be reliable.
Read Best Reviews of TRENDnet 300Mbps Wireless N Access Point TEW-638APB (Black) Here
This works well as far as speed, but needs a daily reboot. Not sure what the issue is, as it just drops all connected devices.Want TRENDnet 300Mbps Wireless N Access Point TEW-638APB (Black) Discount?
Sometimes you can use a wireless adapter to get your device on your network. Sometimes your TV or Blu-ray player leaves you with no option other than a wired connection. This device allows you to put a switch or hub anywhere in a typical home or plug any network cable directly into it for a network connection.Alternatively, two of these can tie remote areas of a network together wirelessly without having this emulate a wireless adapter. You can also use this by plugging it into your network in locations where wireless devices, such as laptops get weak signals. You could even have an individual laptop use this instead of its built in adapter if it has trouble picking up on your network from remote areas of your home.
You start off by connecting this device to a single computer so you can configure it. You can bring it up with a web browser, and bypass the need to install the configuration software on your PC. However, if its default IP address is out of the range of your subnet mask, you would have to manually assign an IP address and subnet mask to your computer, and set them back after configuration.
That method is a common way to configure similar devices. It can make things easy, or it might seem confusing enough to drive you away. If so, you merely use the software on the CD, which finds the device and walks you through the configuration without the problems above.
The way the modes of operations work could be explained better in the manuals, and there is an assumption that you already understand the related network concepts and types of wireless security. The method of configuration is not what you might be typically used to. There is some ambiguity in certain areas where it is not clear whether a field applies to the device or to the router you are connecting to.
It's pretty clear that they were not willing to hire the native English speakings consultant to maintenance of wording the screens. If you understood that last sentence, you should understand their configuration screens too.
In order to work with my network, I needed to set up a profile for the wireless network name used by my router. Once I got the security information in there, things worked like a charm. It also did a good job of finding other networks within range.
One day I found that my connection speed was not only fast, but far exceeded what my Internet provider gives me. After a little investigation, I found that at some point, this device connected to the network with the strongest signal, which was an unsecured router belonging to a neighbor. That left my network vulnerable since it had a non encrypted connection, plus security and firewalls assumed I had a secure wired connection. Their support group told me there is no way around that.
Since your devices plug into this (or a hub or switch that's plugged into this) they act as if they were any other wired devices. You do not see a WiFi icon in your system tray nor do you see a signal strength indicator. So there's no way of seeing what network you get a wireless connection to unless you look at what network this independent device got connected to. This would not be an issue if you use two of these devices to bridge wirelessly, but that should not have been necessary.
At some later point, I found that it tried to give a warning message before attempting to connect to a non-secure network, which is something their tech support group told me would not happen. I wish there were an explanation for why it connected to one on its own before without such a warning. You would never see the aforementioned warning unless you went to the device to try to figure out why you had no network connection. It would have been nice if they had something similar to what you have with a bi-directional printer where a status icon in your PC tray shows the state of the remote device.
If you have things set up, your router stays on and connected, and the device stays powered on, you can get excellent performance. If you lose the connection while you are updating your router's firmware, or for any other reason, I can't tell you what this device will do on its own in the interim. It still works well enough that I use it and it's the best practical alternative for me.
Save 42% Off
No comments:
Post a Comment